P104E Engine Trouble Code

When you check engine light came on code P104E the reason should be . However your vehicle's manufacturer may have a different definition for the P104E OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

When the DTC check engine light comes P104E code on the first you can check is the gas related maybe gas cap. Pull over, retighten it, and take a look at the cap to see if it has any cracks inside. Go on driving and to see if the check engine light turns off automaticly. On the other hand, you can buy a gas cap for about $4.5 at an auto parts store. All you need to do is take the old one take off and take on the new one. If you've already bought it to the store, you might as well just replace the cap. While not car-threatening, it's good to take care of this right away to improve gas mileage/km.

P104E Code Meaning :

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P104E OBD-II Diagnostic Powertrain (P) Trouble Code Description

P104E engine trouble code is about Engine Shutoff Solenoid Malfunction. Injector Circuit Malfunction - Cylinders and Engine Shutoff Solenoid Malfunction causes most of code P104E.

Reason For P104E Code

P104E the main thing to check is to verify the operation of the VCT solenoid in the engine. You're looking for a sticking or stuck VCt solenoid valve caused by contamination. Refer to vehicle specific service repair manual to perform component tests for the VCT unit.

How To Repair P104E Code

Before starting let's see P104E repairing process steps:

• Qualified technicians will begin by using a scan tool to access P104E code stored in the ECU.
• Technicians will note P104E code present and any freeze frame data associated with them.
• After all, if you sure the engine trouble is finished, the code will be cleared.

As you idle at a light or before positioning your vehicle in gear and you see that your engine is starting to create strange sounds, switch your oil filter and also inspect the pressure regulator to attempt and adjust the error. If you struggle to start your vehicle and notice it fails to turn over right away, it can also indicate a defective fuel pressure regulator.

The computer installed in each fuel-injected vehicle has to be aware of two factors before it can solve the proper cold-start air/fuel compound: the engine coolant temperature and the exterior air temperature. Your symptoms are exactly the same to a faulty engine coolant temperature sensor (ECT). The computer is measuring an air/fuel compound that is excessively meager.

Diagnosis Of Engine Error OBD Code P104E

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P104E trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P104E code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.